Here down the page you can discover some excellent news related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also often, tiling skills. Replacing an old tub with a new one is additionally a reasonably challenging task. If the old tub is easily available, the task can move speedily; if you have to open a wall to remove the old tub and also place the new bath tub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will require a helper to leave the old tub as well as embeded in the new one. See to it you have actually qualified on your own for the work and fit attempting it. Instead of hiring a professional to take control of a halfway-completed task, it is better to consider employing one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This article will certainly help you mount a brand-new bath tub in your shower room if you have actually currently purchased a new tub and also don't need to change the arrangement of your previous water system pipelines.
Your devices and material checklist should make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome due to the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Prior to moving on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin making certain that the washing machines are in place between the faucet and the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Using the two wooden boards under its feet, position the bathtub in the called for position. The wooden boards are helpful in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the level checks out level.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the same for the other faucet.
Turn on the water supply and inspect all joints as well as brand-new pipework for leaks and tighten them if required. Fill up the bath tub and likewise examine the overflow outlet and also the regular outlet for leakages.
Lastly, fix the bath paneling as explained in the supplier's user's manual. Tiling as well as sealing around the tub should wait until the tub has been utilized at least once as this will settle it right into its last setting.
Planning for the Installment
To start with, the supporting frame provided with the bath must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps unit to prevent stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, creating the water to pass through the wall surface in between the bathroom and the tiling, resulting in difficulties with moisture and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can securing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealant can crack rather early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the market. It is recommended to fit the tiles utilizing water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that write up on Installing A Bathtub when doing a lookup on the search engines. Loved our write up? Please share it. Help others discover it. Thanks a lot for going through it.
Reliable help? Dial.